Quickcal speedometer calibrator ford f150 code error how to#

Read the Insight Overview section for basic information about how to use the Insight box. They do not need to be redone each time the Insight box is calibrated. 15Ģ1 Calibration Intial Setup Insight Box These steps must be performed the first time the Insight box is powered up and each time it is reset.

Quickcal speedometer calibrator ford f150 code error install#

Install factory cover over hydraulic valve assembly.

Connect 4 pin round amp connector to main Insight or Horizon Harness 6. Connect factory wiring to y-harness and Feathersight harness. Unplug factory harness from pressure sensor and plug in supplied y-harness to sensor. Remove factory cover over valve block assembly. S680 and S Route Feathersight harness following existing combine harnesses and hoses from header connector to pressure sensor at valve block just in front of left front tire. Connect 4 pin round amp connector to main Insight or Horizon Harness 5.

Quickcal speedometer calibrator ford f150 code error manual#

Copyright Headsight, Inc iĤ Table of Contents About Headsight i About this Manual i Installation 1 Installing Terrace Sensors (if equipped) 2 Installing Standard Sensors 4 Install Sensor Wands and Cables 6 Routing Wiring 7 Harness Length Table 7 Install Terrace Sensor Wiring (if equipped) 7 Install Standard Outer Sensor Wiring (if equipped) 9 Install Inner Sensor Wiring 11 Finishing Wiring 12 Install Controller 13 Install Horizon Bridge - Horizon Systems Only Install Feathersight Calibration 16 Intial Setup Insight Box 16 Initial Horizon Setup Calibrate Insight Feathersight Calibration 17 Calibrate Horizon 18 Combine Ground Calibration 19 JD S-Series 19 JD 70-Series 20 Settings 21 Combine Configuration 21 S-Series Series 21 Combine Settings 21 S-Series and 70-Series Combines 21 Horizon and Insight Settings 22 2 Sensor Tilt vs 4 Sensor Tilt 22 Tilt Sensitivity 23 Feathersight - HP Balance 23 Operation 24 Enabling Height Control 24 S-Series Series 25 Overview 26 Insight Navigation 26 How to Navigate 26 Meaning of Status Light 26 Screen Contrast Adjustment 26 iiĥ Resetting Insight to Defaults 27 Updating Insight Software 27 Updating Horizon Software 28 Updating with Horizon App 28 Updating with USB 28 Horizon Status Light 29 Advanced Information 30 Theory of Operation 30 Basic Requirements Advanced Information Insight Reading Voltages 31 Before you Start 31 On the Insight Box Advanced Information Horizon Overview 32 Detailed Sensor Voltages 32 Signals 32 Errors 33 Pinpoint 33 Access Combine Settings 34 S-Series Combines Series Combines 34 Enhanced Near Ground Performance 35 S-Series Combines Series Combines 35 Sensor Adjustment 36 Standard Sensor 36 Increasing or Decreasing Voltage 36 Adjusting Down Pressure 36 Terrace Sensor 37 Increasing or Decreasing Voltage 37 Adjusting Voltage Swing 37 Adjusting Down Pressure 37 Diagnostics 38 Troubleshooting by Symptom 38 Troubleshooting by Insight Error Codes 42 Parts 49 Insight Parts 49 Horizon Parts 50 Standard Wheat Sensor HT Terrace Wheat Sensor HT FCC and IC Compliance Statements 53 STATEMENT OF LIMITED WARRANTY 54 iiiĢ0 Installation Install Feathersight All 70 Series and S550, S660, S Route Feathersight harness following existing combine harnesses and hoses from header connector to pressure sensor at valve block just above header accumulator in front of rear left tire.

Headsight s products are protected by one or more of the following US Patents, ,, and other patents pending. Suggestions If you have any suggestions to improve this manual please call or com. All other trademarks are property of their respective owners. Disclaimers Headsight, Horizon, Pinpoint, Insight, Foresight, Feathersight Truesense and Truesight are trademarks of Headsight, Inc. This icon designates an important instruction.

This icon indicates a special tool needed for a given task. This icon designates information of which you should take note. An index is available in the front of the manual to help find technical information for previously installed systems. Note that some sections are labeled to indicate they only apply to certain machines or applications. Complete all applicable instructions in each section before proceeding. 3 About Headsight Headsight Contact Info Headsight, Inc B Road Bremen, IN Phone: Fax: Web: Technical Assistance Phone: About this Manual How to use this manual The instructions in this manual are in the order that they should be completed for new installations.